Are you frustrated because the IGET Bar Plus Pods you want are always out of stock, causing your vaping experience to be interrupted?
Don’t worry, and the following steps will guide you on how to refill IGET Bar Plus in 5 handy steps.
- Locate and drill the fill hole
- Aim the hole with your favourite e-liquid
- Squeeze e-liquid bottle, add 300 drops (15ml) e-liquid
- Check for leaks and sit the pod down for 3 minutes
- Align and insert the pod into the Bar Plus device
Now, you can refill your favourite e-liquid into the Bar Plus Pod, extending your vaping pleasure. Let’s dive into the 5 handy steps that will make refilling your IGET Plus a breeze.
Introduction
In this comprehensive guide, we will walk you through the process of refilling your IGET Plus, ensuring that you can continue enjoying your vaping device to the fullest.
Five of our partners have successfully refilled their Bar Plus devices and have recorded detailed step-by-step instructions.
We have combined this with relevant YouTube videos and our detailed step-by-step instructions to ensure that you get the most illustrated and comprehensive guide possible.
Let’s read the detailed guide on how to refill the I GET Bar Plus below.
Prepared Tools For Refilling IGET Bar Plus 6000 Puffs
- Small electric drill
- A 0.6mm drill bit and a 0.5mm screw
- The e-liquid you want to add
- 0.5mm diameter stopper
- Paper towel
The above size of the drill bit and screw is recommended for reference only, and please choose the right size according to the actual situation.
After preparing these tools, it’s time to drill the hole and add e-liquid.
How To Refill IGET Bar Plus Easily?
Now, we can start refilling the empty IGET Pod. Here are the 5 detailed steps to refill your pod:
Locate and drill the fill hole
- Locate the position of the drilled holes:
When choosing the location of the drill holes, make sure that the location chosen will not interfere with the normal use of the subsequent pod.
For IGET Plus, it is more appropriate to choose the side seam, as shown in the picture. - Choose the right size drill bit:
According to the diagram, choose the size of the screw according to the diameter of the hole, and then choose a drill bit larger than this size.
If you drill a hole with a diameter of 0.5mm (0.02 inches), you should choose a drill bit that is slightly larger than this size to ensure that the screw will fit easily into the hole.
Generally, you can choose a 0.6mm or slightly larger drill bit with a 0.5mm crew. - Install the drill bit and the screw into the mouth of the electric drill:
Insert the selected drill bit into the port of the electric drill and insert the screw into the drill bit.
Then, make sure they’re held firmly in place to avoid loosening or falling off when operating. - Hold the drill in your hand and rotate the front end:
Hold the front end of the drill with one hand and ensure it stays firmly in place.
Then, manually rotate the front end of the drill with moderate force so that it is gripped by the drill and ready to drill. - Slowly turn the drill clockwise:
Holding the handle of the drill in your other hand, begin to slowly turn the drill clockwise with moderate force and speed.
Be careful not to use too much force, as this may damage the IGET Vape Pod. Keep turning until the screw can be easily inserted into the hole, and it means you’ve done.
When performing these steps, be sure to keep your hand steady and operate carefully to avoid accidental injury.
If this is the first time you drill a hole, it is advisable to practise beforehand and ensure that you understand the details of the operation to ensure safety and accuracy.
| Drill size | Diameter (in) | Diameter (mm) |
| 0.4 mm | 0.0158 | 0.4000 |
| #78 | 0.0160 | 0.4064 |
| #77 | 0.0180 | 0.4572 |
| 0.5 mm | 0.0197 | 0.5000 |
| #76 | 0.0200 | 0.5080 |
Aim the hole with your favourite e-liquid
Now, open the e-liquid bottle cap and align the bottle opening with the fill hole of the IGET Pod.
Slowly insert the spout of the bottle into the filling hole, making sure to align the pod’s hole so that the liquid is injected into the pod.
Squeeze e-liquid bottle, add 300 drops (15ml) e-liquid
Then, slowly and steadily squeeze the e-liquid bottle to allow the liquid to drip and flow into the fill hole.
As the 16ml capacity Bar Plus Pod is opaque, you will not be able to see the level of the liquid.
In order to avoid overfilling and spilling, typically, the volume of e-liquid per drop is about 0.02 to 0.05ml.
If your dropper is 0.05ml per drop, then 20 drops would be equivalent to 1ml, and to fill a 16 ml IGET Plus Pod, roughly 300 drops (15ml) of e-liquid would need to be added.
Leave a little bit of space out to prevent spillage.
After adding the e-liquid, wipe the surface of the IGET Pod with a paper towel to make sure there is no liquid residue or spillage.
Check for leaks and sit the pod down for 3 minutes
Firstly, carefully block the hole using a 0.5mm diameter rubber stopper to ensure a complete seal to prevent the e-liquid from leaking during subsequent vaping.
Next, allow the e-liquid-filled IGET Pod to rest for about three minutes. This allows the liquid to fully permeate around the heating coils, avoiding a burnt flavour when vaping.
Align and insert the pod into the Bar Plus device
Reinstall the refilled IGET Pod into the device, making sure that the bottom of the pod is aligned with the device’s slot.
The device has an easy-to-connect magnetic connection. So, insert the IGET Vape Pod gently into the device slot.
When you hear a click, this means that it is fully embedded and securely fastened. You can enjoy your vaping.
How To Refill IGET Bar Plus Online?
You can also refer to other vaper’s experiences online, and the following screenshot is from a YouTube review.
If you would like to know more about the experiences shared by vapers, please click on YouTube.
Precautions Before Filling
Before filling your IGET Vape Pod, please follow these precautions, especially being careful to use the drill to avoid danger.
Before filling e-liquid, first of all, please make sure your working area is clean and stable and far away from any flammable materials to avoid unnecessary danger.
If this is your first time using the drill, make sure you read the guide to using the drill and measure and determine the proper size hole diameter of 0.5mm before drilling the hole to avoid damage to the pod and inconvenient vaping.
When adding e-liquid, make sure you drip the e-liquid slowly and smoothly. The dripping volume should not be more than 16ml to avoid overfilling or overflowing.
By taking these steps, you can enjoy a more enjoyable vaping experience by refilling your vape device more safely and easily.
How To Know When IGET Bar Plus Pod Is Empty?
Typically, a Bar Plus vape will support 6000 puffs, which will last 12-25 days. If you’re a heavy vaper or a deep vaper, you’ll use it up faster.
In any case, if during vaping you notice the following phenomena it means that the e-liquid level is low:
😔Less vapour
If there is less e-liquid, the atomiser is unable to heat enough e-liquid, resulting in a reduction in vapour volume.
😢Diminished flavour
If the e-liquid is reduced, it means that the ingredients (PG, VG) have been diluted, resulting in a reduction in their concentration, which makes the flavour diminished.
🥵Burnt taste
When the e-liquid is low, the atomiser starts to heat up the coil and wick, resulting in a burnt taste.
If you’re experiencing these signals, it means it’s time to replace or refill your nearly empty pods with the right e-liquid.
What’s the right e-liquid? Read on to the next section where we will explain this in depth.
Using The Right E-liquid To Refill In IGET Bar Plus Pod
Different brands and models of vapes may contain different percentages of the e-liquid formulates.
If you use incompatible e-liquids, you may experience bad odours and an unpleasant experience.
Therefore, it is important to choose an e-liquid that is compatible with your device. So how do you choose the right e-liquid? Have a look below:
👍Choose an e-liquid of the same product model, and this is the most direct and simple way, there is no need to worry that the e-liquid is not suitable for the IGET 6000 device.
If the brand doesn’t provide refill liquid, then you can look for other brands of e-liquid with the same flavour.
💁🏽Before that, find out the percentage of the IGET Bar Plus e-liquid formulae, such as the VG/PG ratio and nicotine content.
Make sure that the e-liquid formulation and percentage of ingredients that you buy match those in the I GET Bar Plus e-liquid.
💡If you want to try new-flavoured e-liquid, first empty your Bar Plus Pod of any residual e-liquid, clean it with alcohol, and then empty and dry the pod before filling it with the new one.
The above methods will help to keep the true flavour of the e-liquid and take your vaping experience to the next level.
Why Should Sit Bar Plus Pod For 3 Minutes After Priming?
After filling, please leave it for a while to ensure that the e-liquid fully penetrates into the coil and cotton wick. Generally, the recommended waiting time is 3 minutes.
If you start using without proper resting, it may cause the coil to dry out, which may cause burning or bad flavour.
Therefore, this step is critical that sitting your pod down for a while ensures that the coil and cotton wick are fully saturated, resulting in better flavour and vapour volume.
How To Open IGET Bar Plus?
The IGET 6000 is a pod vape. If you want to add e-liquid to it, the first step is to remove the pod. Removing the pod is very simple, and here are the specific steps:
- Locate and identify the pod section on the IGET Bar Plus device: The pod is the one with the mouthpiece, usually located at the top of the whole IGET 6000.
- Pinch the top pod with one hand and grab the device bottom with the other hand.
- Easily remove the pod from the device by gently pushing the pod upwards.
Please ensure to be careful and cautious when removing the pod to avoid any damage. Once the pod is removed, you can add e-liquid to the IGET 6000.
What Is The IGET Bar Plus Charging Time?
Typically, the charging time for the Bar Plus vape is 30 minutes to 1 hour. Prolonged charging may cause the battery to become overcharged, which can negatively affect performance and flavour.
It is best to charge when the battery is down to 20%, when you may feel the vapour weakening or the indicator light flashing. Also, unplug the unit promptly to avoid overcharging.
The estimated lifespan of the IGET Bar Plus battery is approximately 300 charge cycles and the IGET Bar Plus battery life is expected to last around 300 days under normal conditions.
However, factors such as charging habits and temperatures can influence this duration.
If you want to know the steps to charge IGET 6000, please check the charging guide below.
How To Recharge IGET Bar 3500?
If you’re seeking how to recharge IGET Bar with Samsung charger or Android charger, the following instructions will be invaluable.
- Prepare tools (pliers, scissors, power socket, paper towel and a DIY charger)
- Open an IGET Bar
- Take out the battery and tank
- Connect the wire and turn on the socket
- 4 recharges, 1-2 minutes each
- Reassemble IGET Bar
If you’re unsure how to magic a Samsung or Android charger into a DIY charging, you’ll find detailed steps below.
Verdict
Hopefully, this refilling guide can provide you with a method and a reference for your needs.
However, the Bar Plus vape is designed for the convenient replaceable pod system that you don’t need to manually add e-liquid.
It simplifies the e-liquid refilling process, particularly when on the move.
Once the e-liquid runs out, you can easily replace it with a new I GET pod and continue to vape seamlessly.
FAQ About How To Refill IGET Bar Plus 6000
Is the IGET Bar Plus refillable?
In accordance with the official instructions, it is not recommended to refill the IGET Bar Plus with e-liquid to ensure safety and ease of operation.
It is designed as a Pod Vape. After using the e-liquid, simply replace the pod with a new Bar Plus Pod refill to continue your premium vaping experience.
How do you use the IGET Bar Plus?
Firstly, unpack the plastic seal.
Then, align the bottom of the pod with the magnetic suction on the inside of the Bar Plus device and gently push it in until you hear a click, which indicates successful insertion.
Then, simply insert the pre-filled pod into the device three times in quick succession, and the white LED indicator will light up to show that the device is ready for vaping.
Finally, because of the automatic activation, it is straightforward to inhale and activate with your mouth.
How many times can you recharge an IGET Bar?
IGET Bar vape is a non-rechargeable disposable vape (Electronic cigarette). Charging is generally not recommended for safety reasons.
How do you open the bottom of an IGET Bar?
Hold the vape steady with one hand, then use pliers to gently grasp its base and connections. Wiggle the connection forcefully from side to side to loosen it.
